Crushing and Mining Equipment
- Crusher Machine
- Jaw Crusher
- Impact Crusher
- Cone Crusher
- Mobile Crusher
- Tracked Crusher
- Sand Making Machine
- VSI Crusher
- Coal Mining Equipments
- Coal Crusher
- Coal Mill
- Coal Washer
- Coal Conveyor
- Coal Mobile Crusher
- Coal Crushing Plant
- Tel: 0086-21-33901608
- Fax: 0086-21-58377628
Batubara Crusher and Batubara Crusher Equipment and Batubara Crusher Manufacturers
Batubara Crusher in the power industry has been widely used. Because it can be to break the coal is so efficient, the use of fluidized bed boiler power plant is very satisfactory. Prevalence of coal crusher, coal is broken because it has the ability to have a qualified and particle size and low cost per ton of crushing, while producing minimal too small particles.Batubara crusher is a ring with a broken rotor impact crusher, crushing ring sling in conjunction with the rotor axis of rotation of the hanging, broken ring for rotation with the rotor-impact exercise, but also hanging around the spin axis motion; broken process is working through the broken ring of two to complete.
Batubara crusher is a new type of two hammer crusher combined device, used to link two sets of rotor at the same time. Is a rotating ring with a broken rotor type crusher, crushing ring on the harness together with the rotor axis of rotation of the hanging, broken ring for rotation with the rotor-impact exercise, but also hanging around the spin axis motion; the crushing process through the broken ring of two to complete the work. When the material into the crushing chamber, the rotation of the broken ring in the first paragraph of the impact of fragmentation. In the second paragraph, beginning on the sieve falls broken particles, further squeezed by the broken ring broken, and discharged through the sieve. A small amount of material you can not be broken into the waste chamber, and then periodically removed from the waste chamber. The regulation of particle size is the sieve through the replacement of different specifications to achieve, the gap between rotor and sieve, according to the need to be adjusted by adjusting the body.
Batubara crusher Works
Batubara crusher can be divided into: sub-stick-type and hammer mill.
Roll Batubara crusher: the use of two motors are driven by Batubara crusher pulley so that the upper and lower teeth on both sides to do opposite movement rollers, roller surface shape of the teeth staggered roll, which met Roll material automatically fall gap, larger than the to broken power than the hammer of the drug, and environmental protection, and will not be too crushed, there is no requirement for water, are full at any time to contribute. Roll crusher for coarse material brittle and soft, medium and fine crushing;
Hammer mill: the material by high-speed rotating hammer blow, and the collision between the materials, extrusion, grinding and crushing effect. Demanding of moisture, the use of impact force broken coal, following a sieve, greater than required to break, less than the screening into the boiler.
Batubara crusher Features
1:Unique displacement technology transfer gap, the hammer of the equipment worn without repair, repeated use of the mobile position, a hammer can hammer with the top three.
2:Dual-rotor up and down two pieces, each thread of the two sets of rotor, rotor so crushed by the higher material immediately the rapid rotation of the rotor of the hammer again, crushing the lower, the rapid collision between cavity material, crushing each other, to hammer powder , the effect of powder materials, direct unloading.
3:Hydraulic electric start case, only one person can easily open and close, not only lightweight and fast, secure, reliable, easy to repair.
4:No mesh grate at the end of Batubara crusher , humidity material, not blocked. Traditional grinder with sieve grate, not suited to high moisture content of 8% of the raw materials, when raw water is higher than 10%, prone to severe congestion, the hammer can not move, the material can not be discharged, and even burning bad motor, seriously affecting production. Mill design does not mesh grate at the end, the moisture content of materials is not strictly required, completely blocking the sieve paste does not exist the problem, but there is a fine powder can not be discharged, repeated crushing of the problem, so crushing, high efficiency, there is no hammer header is invalid abrasion.
5:Combination of hammer wear, wear-resistant high-alloy mill hammer. Combination hammer handle hammer, hammer only for not-for-hammer handle.